HOMEOWNERS, BUILDERS AND architects choose to use low-E Glass in their windows for one reason: energy efficiency. Of Course, low-E glass brings other benefits such as increased Comfort and condensation resistance, but the primary function is Improved energy efficiency – whether the driving force is to meet Building codes or to reduce utility costs. However, those who use Low-E glass must be careful in their selection, as not all low-E Glass is the same.

The impact of sunlight

 All low-E glass improves the insulating value of the window in Basically the same way. A thin coating based on either silver or tin Oxide is deposited on the glass. This coating transmits visible Light, but reflects longer wavelength infrared light associated with Radioactive heat emitted by all warm objects. By reflecting this Radioactive heat back into the room, the coating reduces heat loss From the building, resulting in a lower overall heat transfer Coefficient (U or K).

 

Because of its relative simplicity, there has been a tendency to Compare only the U value for different windows and glazing Options, just as one would do for wall insulation. However, it is Inaccurate to treat a window as if it were an opaque wall, ignoring The effect of sunlight coming through the window. Sunlight is a Significant source of free energy into the building, which can be Either beneficial or detrimental, depending on the building Location. Thus, to accurately evaluate window performance, the Solar heat gain coefficient (SHGC or g) must also be considered, As its impact on energy consumption can be the same or even Larger than that due to the U value. For this reason, modern Window rating programmers such as the European Window Energy Rating System (EWERS) and performance-based building codes Are moving away from considering only U value to formulas Including both U and SHGC.

Comparing performance

 Those who use low-E glass must be aware of both properties, Because although all low-E glass will have a reduced U value, Different products can vary widely in actual performance by having either high or low solar heat gain. In warm climates, where Energy consumption is dominated by air conditioning, windows With low solar heat gain are preferable to reduce cooling Demand. In colder climates where heating is the major concern, High solar gain windows are preferable, as they let in the free Energy of the sun to reduce heating fuel consumption. Special Care must be taken in cold climates, because as the U value is Reduced, the solar heat gain is reduced even further for many Coatings. Therefore, although a low-E glass with a very low U Value appears to be the best choice, it may actually have worse Performance if it has low solar heat gain that blocks the warmth Of the sun and increases heating requirements. For example, the energy rating of an insulating glass unit (IGU)

With U=1.1 W/m2K and SHGC=0.30 is actually worse than an IGU

With U=1.6 W/m2K and SHGC=0.55 for typical homes in the UK and

Denmark, despite the lower U value. The improved insulating level

Is offset by low solar heat gain, which reduces the benefits of Passive solar heating. In conclusion, it is not enough to only look at U value when Selecting low-E glass. The solar heat gain, which can vary widely Between products, must also be considered, based on the local Climate. Window rating systems that include both U and SHGC in A simple energy rating, such as EWERS, is useful tools in making This decision.

Authors & Company Profile

Dr Thomas D Culp is manager of energy policy and New technologies, and Rein de Varies is European Marketing manager, both at Atofina Chemicals Inc, A branch of the oil group Total. Atofina Chemicals Supplies the glass industry with technology for manufacturing low-E coatings. Atofina enjoys leading Positions both in Europe and the world in each of its Three core activities: base chemicals and commodity Polymers, intermediates and performance polymers, and specialty chemicals.

FOR MORE  INQUIRY MAIL US 

glazingshopee@gmail.com

OR

CONTACT 

Prashant Thakkar 

Mobile No : 9324789080

Add:

51, saidham shopping

p.k. road  Mulund west

Mumbai-400080

(0)

Low E glass, E stands for emissivity, was introduced in 1979 and is now a great favorite among contractors. Low E glass works by reflecting heat the same during the winter and summer, using a thin metallic coating on or in the glass. These windows can be installed almost in all regions of the world, but the main factor is related to the building design and window position. As a builder, you can use them for your new projects or even in major renovations, ideally for healthcare facilities as maintaining temperatures is critical in some of these facilities.

 These windows can provide many benefits for the building owner as they can save as much as 50 percent in energy use, provide greater operational efficiency, improved access to daylight and natural views for occupants without increasing energy costs for heating and cooling.

Why choose low-e windows Instead of regular windows?

Low-E windows can provide aesthetic value to building occupants, and they will not reduce the amount of light entering the building while maintaining the natural look of windows. However, windows can also represent a large source of heat gain or loss, because when the right window is not used, it can increase heating costs and A/C usage, making it more costly to operate your building.

Similarly, windows with a poor ability to keep heat in allow warm air to escape the building in the winter, increasing the demands on heating systems. Window manufacturers have developed many new insulating and glazing techniques to improve the performance of windows.

The National Fenestration Rating Council defines five performance areas to consider when choosing windows most suited for your local climate:

  1. Look for Lower U-Factor Values –  These numbers will represent how well a product prevents heat from escaping a home or building. Always look for U-values between 0.20 and 1.20, where lower numbers indicate a product better at keeping heat in.
  1. Lower Solar Heat Gain Coefficient is Better – (SHGC) measures how well a product blocks heat from the sun from entering the building. SHGC is expressed as a number between 0 and 1, with a lower SHGC indicating a product that is better at blocking unwanted heat gain.
  2. Visible Transmittance (VT) measures how much light comes through a product. VT is expressed as a number between 0 and 1 with a higher VT indicating a higher potential for day lighting.
  3. Air Leakage (AL) measures how much outside air comes into a home or building through a product. AL rates typically fall in a range between 0.1 and 0.3 with a lower AL indicating a product that is better at keeping air out.
  4. Condensation Resistance (CR) measures how well a product resists the formation of condensation. CR is expressed as a number between 1 and 100 with a higher CR indicating a product better able to resist condensation.

Not all low-e windows are suitable for all climates, so be sure to choose the right window for the climate where you are building. It is important to note that facilities in warmer climates should install windows with a lower SHGC and those in a cooler climate should install windows with a lower U-factor. Low-e coatings applied to exterior window panes prevent heat gains from exterior radiation; whereas low-e coatings applied to interior windows prevent heat loss.

Manufacturers often offer several low-e coatings with varying degrees of solar gain.

Low-E Windows Benefits and Costs

Windows manufactured with low-e coatings typically cost about 10 to 15 percent more than regular windows, but they reduce energy loss by as much as 30 to 50 percent.

Furthermore, this improvement in the building envelope—particularly when coupled with other strategies that improve the efficiency of the building envelope—ultimately impacts the demands of building HVAC systems. These benefits should be included in evaluating the lifecycle costs of installing efficient windows.

Efficient windows are defined by the climate of the building in which they will be installed. Engineers and vendors are able to make recommendations based on local climate and building orientation. Efficiency improvements to the building envelope directly impact the heating and cooling needs of the building; therefore, HVAC systems should be adjusted accordingly to account for decreased demands on the systems.

FOR MORE  INQUIRY MAIL US 

glazingshopee@gmail.com

OR

CONTACT 

Prashant Thakkar 

Mobile No : 9324789080

Add:

51, saidham shopping

p.k. road  Mulund west

Mumbai-400080

 

(0)

Switchable technology has revolutionised the way we see window privacy.

From offices to homes, windows are a widely known architectural device used to bring a number of benefits to a room that would otherwise see isolation from the outside world.

One such benefit is the wonders of natural light; a traditional window brings a snapshot of the outside world indoors without exposing the occupants to the elements.

As the differences in artificial and natural light are generally understood to impact mood, productivity and health, a source of natural light in a room is an important consideration for designers, architects and occupants.

Blind cords can get easily tangled, especially if they are heavily used
Blind cords can get easily tangled, especially if they are heavily used

However, with these considerations come inevitable complications in the form of privacy. The bigger the natural light source supplied, the bigger the requirement for a privacy solution.

Traditional solutions used to solve this privacy burden usually come in the form of blinds or curtains. Often, these solutions bring with them even more complications, requiring the designer to source a solution that meets all the specified requirements, which isn’t always easy.

For example, coverage inconsistencies in blinds may allow sections of light to spill into the room, creating an irregular light level in the room.

Furthermore, it is well known that blinds and curtains bring with them more operational maintenance than many would like; gathering dust, tangled cords, sun damage and even the basic yet unproductive time wasted in opening / closing them.

Switchable technology solves these problems, as well as bringing new and exciting aspects to window privacy. For example, being able to control your window privacy using an RF remote control from up to 25m away is an efficient novelty that you will become very comfortable with.

Unlike the slow and often noisy motors used in remote controlled blind or curtains, our switchable products change in an instant without drawn-out mechanical humming.

Available from Intelligent Glass in the form of either a retrofit self-adhesive film or a rigid glass screen, these core technologies have been integrated into various products that allows Intelligent Glass to proudly boast one of the most diverse ranges of switchable solutions in the world.

Our switchable products work by changing the state of transparency from frosted to clear using electrically charged PDLC crystals.

When the electric charge is passed through the PDLC layer, the crystals polarise, causing them to change state from frosted to clear. This offers clients an incredibly powerful privacy tool that not only looks stylish but can also satisfy a variety of additional requirements.

The versatility of switchable technology is one of the areas we see it excel and due to the nature of PDLC film, Intelligent Glass is able to use its clean room facilities to manufacture a range of switchable products with specialist options, such as sound insulating glass, double glazed units, fire resistant glass or even bi-fold door options.

Switchable technology also has the ability to be integrated into smart home and office applications, putting users more in touch with their environment than ever, allowing them to change the window from frosted to clear by a simple voice command.

Switchable film can be cut to custom shapes allowing for simple installation in places that would not accommodate blinds or curtains easily
Switchable film can be cut to custom shapes allowing for simple installation in places that would not accommodate blinds or curtains easily

What’s more is that many of our switchable products can be combined with both rear projection and touch screen technology, serving a multitude of possible commercial and corporate requirements, but also offering the opportunity to dream up creative and exciting residential applications.

For example, a switchable glass rear projection screen can be used incredibly effectively in a shop window display for merchandising or even as part of a glass partition, creating an innovative presentation screen in an office environment.

But in residential applications, we have seen specialist switchable products vary from switchable glass stairs to gaming projection glass partitions.

Rolls Royce used a switchable glass projection screen to launch the Dawn in Harrods famous store window
Rolls Royce used a switchable glass projection screen to launch the Dawn in Harrods famous store window

It’s clear that for window privacy, switchable technology is the future solution that will eventually replace the messy, high maintenance and archaic privacy solutions we see today.

But for now, you can invest in switchable technology safe in the understanding that it is a highly impressive aspirational product; that is, not many people are familiar enough with it to be expecting it in your property.

So when you make that switch in front of your guests for the first time, you are sure to make a big impact. Not forgetting, of course, the ways in which switchable glass will change your daily life for the better.

Window privacy is an aspect that impacts almost everyone, so it’s important that it is considered appropriately.

SOURCE

Intelligent Glass

 

(0)

Over the last decades, stainless steel has been recognized as a versatile high-end material and became a dominant design element in an increasing number of façade and curtain wall projects.

The Glass Façade – an Eye-Catcher

Façades are often the business card of a building. The lobby gives a first message of prestige to its visitors when entering the building. Therefore, it is no surprise that architects and designers accurately select and define materials for these areas. More and more of them turn to stainless steel for their curtain wall projects.

High Quality Curtain Wall Profiles

Montanstahl brings over 30 years of industry experience and excellence in the production and supply of high-quality special shapes in steel and stainless steel. Our laser welded curtain wall sections differ considerably from conventional fillet-welded sections.

The laser weld seam is small, neat and barely noticeable. Montanstahl usually manufactures its laser profiles by welding together high precision laser-cut flat bars and occasionally the stainless steel profiles are build up using press brake sections, hot rolled or extruded special shapes.

The Right Solution for a Prestigious Curtain Wall Façade

In a steel-glass curtain wall, the mullions and transoms must grant sufficient strength to support the load of the façade. The weight of the glass panels and the resistance against the wind load assure this. The more glass and less mullions contrators use, the more majestic and transparent the façade will result.

Extruded aluminum profiles are the most common material for curtain walls. However, they are not strong enough for such high span facades. Here the preferred choice clearly becomes mild steel, thanks to its three times higher e-modulus and for more prestigious applications stainless steel.

Stainless Steel Profiles for a Curtain Wall

Laser Welded and Sharp Edge Curtain Wall Sections

Montanstahl laser welded curtain wall sections are custom-made. Structural engineers can specify the width, height as well as the web and flange thicknesses according to the static requirements.

They also calibrate the weld penetration precisely, according to the structural load requirements of the curtain wall and minimizing distortion and stress.

It is also possible to combine different material grades, so called black and white combinations, where some parts are in mild steel and other parts in stainless steel. This all results in a wide matrix of solutions that givetotal design freedom to architects and engineers.

Another plus is the sharp contour of the shape that generates a precise cut between light and shadow. Architects appreciate this very much.

Stainless Steel Curtain Wall Profiles

The majority of curtain wall mullions and transoms are designed with a sideline of 50 or 60 millimeters. The depth, or height of the sections, results from the structural requirements of the façade. The taller the façade the greater the depth of the section and/or steel masses used in the flanges.

The most popular mullion and transom designs used in steel-glass curtain walls are rectangular hollow sections (RHS) and stainless steel tees.

Stainless Steel Hollow Sections

RHS are a very common and functional design for mullions and transoms. Conventionally welded RHS have the inconvenience of rounded corners (with radius equal two times the material thickness).

Laser welded RHS not only have crisp outside corners independent from thickness, but they are optimized to the required loads. Increasing the wall thicknesses, mainly in two opposite flanges, is easy.

Therefore, the majority of laser welded RHS used as mullions in facades have different material thicknesses in flanges and webs to increase the moment of inertia.

Stainless Steel Tees

Laser welded stainless steel tees with sharp corners are an ideal solution for objects where the main criteria is to achieve a minimalistic façade with slimmest possible sidelines. Thanks to this attribute, steel and stainless steel T-sections have become a very requested design for any curtain wall.

Free Forms and Tailored Shapes

Free forms are the ultimate step in customizing façade designs. If an architect wishes a unique individual design for a curtain wall project, then laser welded profiles are the answer. No other technology enables a curtain wall in steel or stainless steel like the laser welding technology does.

90-degree angles are not a must and arrow shaped, we can also fabricate trapezoidal or triangular geometries easily.

The Aesthetics of Stainless Steel

From an aesthetic point of view, stainless steel is notable for its inherent beauty. Plus, it easily blends with other materials. It has a subtle sheen, which does not overwhelm or intrude on other design and colour elements. Instead, it complements, reflects and highlights surrounding materials.

Shot Blasted Standard Finish

Montanstahl supplies its stainless steel curtain wall sections with a shot blasted standard surface execution. Over the years, this has become a recognized and accepted surface finish. Anyhow, in some prestigious projects, this standard finish is not enough and the designer requires a refined polished surface.

Polishes Finishes

For a common polish or hairline finish up to a grit of 240/320, Montanstahl has in-house equipment. For a higher level of finishing, like mirror polish, we collaborate with specialized external polishing companies. These will do the job according the required specifications.

There are profiles that are so demanding and have such a complex geometry, that we must pre-polish parts of it in our workshop. Then the contractor also mirror polishes some parts before welding them to final shape and then polish them finally.

Curtain Wall Projects

A mirror polished curtain wall project is the prestigious building of the Novartis Consolidation Centre in New Jersey (architect: Rafael Viñoly Architects), USA and the University Campus of the Russian Bank Sberbank(architect Erick van Egeraat).

For the project in Athens, Greece of Stavros Niarchos Foundation for the new National Library (architect: Renzo Piano), we produced more than fifteen different tailored special hollow sections.

Also for the new Cadillac Experience Centre in Shanghai, the stainless steel rectangular hollow sections were tapered for the corner mullions. This solved several installation problems on site.

Another special project still under construction is the Paddington Station’s Crossrail in London. Tailored rectangular hollow sections with a mirror-polished surface will become the structural elements for bombproof glass there.

For the façade of the Centro Botin in Santander, Spain, designed by Renzo Piano and realized over the seawater, major parts of special structural curtain wall sections are made in highly corrosion resistant duplex steel.

We also supplied special tailored stainless steel tees and stainless steel angles for the construction of all external staircases.

Last but not least, Montanstahl supplied nearly one kilometer of stainless steel hollow sections for a new concept of the skyscraper “The Beirut Terraces” in Lebanon, designed by Herzog & De Meuron. The surface execution is mirror polish.

SOURCE
Capture

(0)

Kite Glass is proud to have worked with Delta Fabrications to bring aesthetically pleasing and structurally safe stairways and balustrades to the new multidisciplinary research centre.

The Big Data Institute (BDI) is a state of the art building at Oxford University’s Old Road Campus. Set to open in 2017 the research centre will look into the causes and consequences, prevention and treatment of disease.

Kite Glass Case Study: Big Data Institute (BDI), OxfordOnce complete, the BDI will accommodate 522 staff and bring together world-leading researchers.

The pioneering data centre will store, analyse and process vast amounts of health-related digital data with the aim of providing new insights into illnesses and treatments worldwide.

Kite Glass is proud to have worked with Delta Fabrications to bring aesthetically pleasing and structurally safe stairways and balustrades to the new multidisciplinary research centre.

We provided 16.89mm, 20.89mm, 21.5mm and 25.5mm heat soaked SentryGlas® covering 141m2, 62m2, 21m2 and 50m2 respectively.

Kite Glass was one of the first in the UK market to successfully process this product and has been doing so since 2006, and is therefore recognised by Kuraray as an officially approved supplier of SentryGlas®.

 

 

SOURCE:

capture

(0)

PROJECT NAME :.  PRESTIGE GARDEN, Siliguri

Address :. Devi chaudrani road ( pipe line ), salugara siliguri wb., Salugara, Siliguri, West Bengal

Property Status:. Under Construction

Area :  1140 sqft
add_watermark
For further information mail us on glazingshopee@gmail.com or Call us +91-9324789080
(0)

The coloured solar panels and photovoltaics from Emirates Insolaire LLC, a joint venture of Dubai Investments PJSC and SwissINSO Holding Inc., a Switzerland-based pioneer in solar technologies, will soon dress up buildings across Dubai as the Emirate is fast moving towards a sustainable future powered by renewable energy sources.
Emirates Insolaire, which pioneered the KromatixTM coloured solar technology – the first-of-its-kind in the world, also announced that discussions with different authorities and companies across Dubai are in final stages on installing the panels in buildings. For the first time in history, photovoltaic panels from Emirates Insolaire can be adapted to any façade without compromising on the design and aesthetics of the building.
The solar panels from Emirates Insolaire also offer high efficiency in generating energy from solar power, with each photovoltaic module capable of generating 170 to 190 watts per square meter for roof installation or 110 to 130 watts per square meter for façade installation.
Rafic Hanbali, Managing Partner of Emirates Insolaire, said: ““Emirates Insolaire has ushered in a paradigm shift in solar applications with its energy-elegant dress on buildings and the company is in negotiations with authorities and companies to implement this. The KromatixTM solar panels can supply between 20% and 60% of needed energy for a building. For certain industries with large roof and façades, this can go up to 100%. Emirates Insolaire expects to play a pivotal role in the regional solar sector growth.”
Emirates Insolaire is also showcasing the KromatixTM technology at Solar Middle East exhibition [stand: Z2 B58] at Dubai World Trade Centre till February 16, 2017. Over 140 exhibitors from 85 countries are participating in the exhibition.
The company is eyeing a strong growth amidst a massive potential for photovoltaics and solar thermal power in the Middle East & North Africa [MENA] region. An estimated 2,000 MW of solar energy projects in the region are likely to be tendered, and by 2020, $50 billion will be invested in the region’s solar sector, according to official estimates, with the UAE and Saudi Arabia taking the lead.
The Gulf Cooperation Council [GCC] countries are expected to increase their installed solar capacity 50-fold between 2015 and 2025, with Saudi Arabia announcing plans for an additional 9.5 GW of renewable energy by 2030.
SOURCE :
dubai-investments-logo
(0)

Designed by the Architecture agency AIA Associated, the new headquarters of the “Credit Mutuel” in Nantes is spread out on 2 main buildings & 8200 sqm of glass facades.

In order to diffuse a natural light in the working areas, a double-skin façade has been implemented.

For the construction of the glass sunshades, Sadev supplied more than 6500 rotules from type R1103.

For additional information, please read the Project presentation.

Photo credit: Gaël Arnaud through Ouest Alu

SOURCE :

capture

(0)

Emplas has added the new Dynamic 2D-C hinge, which features a unique patented horizontal adjustment system, to its composite door range.

With a traditional appearance but packed with technology, the 2D-C from SFS Intec, delivers strong aesthetics but significantly increased flexibility in fitting through two-dimensional adjustment of the door.

This includes simple Allen key adjustment to increase the horizontal gap between the sash and frame, plus vertical adjustment.

Kush Patel, Operations Director, Emplas said: “There’s been a growing demand from installers for increased flexibility for adjustment in a hinge with a traditional appearance.

“The Dynamic 2D-C hinge features a slim-line body which sits neatly over the air-gap of the door and delivers a high level of adjustment, without impacting on security.

“This creates a more consistent pressure across the gasket, improving performance and weather tightness, reducing the chance of a call back – its true ‘fit and forget’ technology.”

The Dynamic 2D-C hinge is available in numerous solid colour options and the high performance Endurabrite chrome and gold finishes, which are guaranteed to withstand harsh environments whilst still retaining their appearance.

It has also been fully impact tested achieving an indicative pass of 13.4kN on a standard 44mm composite slab.

The Dynamic 2D-C hinge represents the latest enhancement to Emplas’ Composite Door Range. Supplied as Secured by Design as standard, this includes a comprehensive choice of composite door styles and finishes, plus a highly competitive range of six specially selected door styles.

Available to its customers with a lead time of just 5-days,this includes the Esteem Solid, and part-glazed, Elegance, Eclat Arch, Esteem, Elegance Arch and Eclat style options.

They’re available in standard, black, blue, green, red, rosewood and white, with specially selected Kara Zinc, Scotia Zinc, Andorra, Zinc and Stippolyte and clear glazing options.

These combinations make up 65% of all Emplas composite door orders, which means that, two thirds of its composite door range as a whole, is available in a 5-day delivery time.

“This is a simple but really competitive offer both in its lead time and price point. It gives installers access to the doors that they sell most of with a really rapid turnaround”, said Kush.

“Our composite door range is also constantly evolving to better meet customer demand as illustrated by the addition of the Dynamic 2D-C. This is on top of an SBD as standard offer”, He adds.

Dynamic 2D-C hinge at a glance:

  • Fit and forget – eliminates remedial work on sagging doors

  • Two-dimensional direct adjustment for perfect threshold seal

  • Easier installation – door leafs can be removed and refitted with less hassle by a single installer, making operation safer and financially beneficial

  • Fixed gasket pressure which means the weather seal always remains exactly as pre-set in the factory – eliminating onsite installation errors

  • Dog-bolts not required to meet security standards

  • Constant 4mm adjustment space – no need to adjust top pin in relation to the bottom pin

For more information on Emplas visit www.emplas.co.uk , email info@emplas.co.uk or call 01933 674880.

SOURCE : emplas

(0)

Multiple glass options offer customized ways to suit different building needs.

Different buildings have differing needs for aesthetics, performance, and functional operations. Few building materials have as great an impact on all three of these areas as glass since it plays a unique and important role in building design and the environment. The use of glass in buildings affects design, appearance, thermal performance, and occupant comfort. Historically, glass was used mainly for windows to admit air and light, but with advanced manufacturing options and the need for high-performance buildings, it is now integral to interior and exterior architecture. From facades, skylights and walkways to revolving doors and glass box extensions, glass is being used to do much more than just let light in. Therefore the selection of the right types of glass is a crucial element of the design process to create solutions that address thermal control, energy efficiency, views, and lighting quality as well as light quantity. Architects who understand the full range of possibilities available from glass manufacturers are able to use them as a complete palette to create designs that excel in all areas.

Glass and Glazing Overview

The main ingredient of glass is SiO2 (silica sand). During the first half of the 1900s the predominant glass manufacturing technology was to create plate glass from molten SiO2 which moved along rollers while still heated. This created imperfections in the surface of the glass that needed to be ground and polished to produce parallel surfaces that were optically clear. During the 1950s and 60s Sir Alastair Pilkington invented and perfected the process of creating float glass which has become the current world standard for the production of high-quality glass. Float glass is manufactured by melting sand, soda ash, dolomite, and limestone, along with other minor batch materials to produce a continuous glass ribbon. The molten glass flows from the furnace and “floats” over a bed of molten tin where it spreads out to form a level sheet with virtually parallel surfaces. It is then carefully cooled to anneal the glass—a process that minimizes the internal stresses enabling it to be cut.

Common terms and performance criteria relevant to glass include:

U-Factor: The thermal conductance of a material. The lower the number the better the insulation or thermal control. U-factors are often measured at various points in a window unit including the center and the edge of the glass.

R-Value: The thermal resistance of a material. R-values are the reciprocal of U-Factors (R= 1/U) meaning a higher number represents higher thermal resistance.

Solar Heat Gain Coefficient (SHGC): The ratio of solar heat gain through glass relative to the amount of incident solar radiation. The lower the number thegreater the solar control.

Visible Light Transmittance (VLT): The percentage of light in the visible spectrum that is transmitted through the glass. The higher the number, the greater the amount of light that passes through the glass, regardless of its color. Visible light makes up about 47 percent of the solar spectrum, with wavelengths from 380 to 780 nanometers.

Ultraviolet Light (UV): About 2 percent of the solar spectrum with wavelengths ranging 300 to 380 nanometers. Although ultraviolet light is invisible to the human eye, long-term UV exposure contributes to fading and aging of organic based materials. 40 percent of fading comes from visible light other than UV.

Infrared (IR): About 51 percent of the solar spectrum, with wavelengths ranging from 790 to 3,000 nanometers.

Low Emissivity: Emissivity is the ability of a surface to reflect or emit heat by radiation. The lower the number, the more efficiently the object reduces radiative heat gain or heat loss, which means a lower U-factor and better insulation.


Photo courtesy of Pilkington North America

Advances in glass technology give architects a wide variety of choices to meet design requirements for performance, aesthetics, and comfort.

Variations in the float glass manufacturing process or additional actions immediately after allow for the creation of different types of glass and glazing. Each general type is produced to create different properties of light transmission, thermal characteristics, or other inherent structural properties. Several of the common types can be briefly summarized as follows:

Coated Glass

During float glass manufacturing, pyrolytic coatings are incorporated into the glass by depositing microscopically thin layers of metallic oxides using a process known as chemical vapor deposition (CVD). Having this type of hard pyrolytic surface fired on at over 640°C (1,200°F) make pyrolytic products more durable than sputter coating which is a low pressure technique that deposits coatings using physical vapor deposition, typically without applied heat. The pyrolytic process creates extremely durable coated products that can easily be handled, transported, and processed. These products typically combine low emissivity, solar control, low reflection, and self-cleaning properties. In addition, because the pyrolytic surface doesn’t degrade like a sputtered coating, it can be warehoused locally for availability, reducing project lead times across the country and around the world.

Heat Strengthened

Annealed glass is subjected to a special heat-treatment in which it is heated to about 680°C (1256°F) and afterwards cooled. When it is cooled slowly, the glass is twice as strong as annealed glass. If it does break the fragments of the broken glass may remain in the frame but are large. Heat strengthened glass is not recognized as a “safety glass” by typical building codes.

Tempered Glass

Tempered glass is at least four times stronger than annealed glass. When broken, it shatters into many small fragments which reduces the potential for major injuries. This type of glass is intended for glass facades, sliding doors, building entrances, bath and shower enclosures, and other uses requiring superior strength and safety properties.

Laminated Safety Glass

Laminated glass comprises two or more layers of glass bonded together with a plastic or resin interlayer. If broken, the interlayer is designed to hold the glass together. Virtually all glass types can be laminated and the thickness and types of interlayer can be varied to provide ballistic, bomb or physical attack resistance. Laminated glass also provides attenuation of sound and can typically be cut and further processed.

Image courtesy of Pilkington North America

Pyrolytic coatings are applied during the glass manufacturing process to create a product that provides high performance and durability.

Low-e Glass

The type of coated glass provides thermal control and enhanced insulation, as well as control of solar heat gain when combined with a solar control glass in either a monolithic or insulating glass unit. Low-e coatings reduce the emissivity of the glass surface meaning the glass provides greater insulation by reflecting heat back towards its source and can also be designed to absorb or reflect solar energy. As such, low-e coatings are useful for reducing both solar heat gain and heat loss. For a sense of context, uncoated glass has a typical emissivity of 0.84 while a low-e coated glass could have an emissivity of 0.15. This means only 15 percent of heat is absorbed and re-emitted while the rest is reflected. Different combinations of low-e coatings can be used in an insulated glass unit to provide the desired performance.

Insulating Glass Units

Insulating units are two or more panels of glass bonded to a perimeter spacer material with a hermetically sealed airspace. The primary benefit is to improve thermal performance with better U-factors as well as solar control by influencing the Solar Heat Gain Coefficient (SHGC). Most types of processed glass can be incorporated into an insulating glass unit to adjust and fine tune its overall properties accordingly. Double glazed units are the most commonly used type of insulating glass unit, however in some climates the use of multi-cavity triple glazed units is increasing in response to tightening energy codes.

Design Issues and Glass Solutions

With a basic understanding of different manufactured glass types, we can now turn our attention to particular issues that are commonly addressed in building designs to determine the best type of glass that may be suitable solutions.

Controlling Solar Gains

A great deal of the increasing emphasis on energy use in buildings has been placed on the building envelope and particularly on glass and glazing. With the increasing sensitivity toward reducing fossil fuel usage in particular, energy codes and standards have been becoming more demanding in terms of the performance of glazing. They have steadily been raising the bar on performance such that glazing needs to be carefully addressed during design and appropriately specified to both anticipate and achieve the intended energy performance.

The first and perhaps most significant point about energy performance when it comes to glazing is that the building location and the orientation of the glass in respect to the sun (i.e. solar orientation) are the starting points. There is no single universal solution across all locations and all orientations. Energy codes and ASHRAE Standard 90.1 recognize this fact by identifying and defining separate U.S. climate zones which are the basis for determining all other aspects of energy performance and code compliance. From there, the codes require varying degrees thermal performance or solar control depending on location and orientation.

Many commercial buildings are located in warm or temperate climate zones with internal operations that generate heat inside the building (i.e. internal heat loads). Hence, more energy may be needed to cool the building than to heat it in a typical year. Controlling the amount of heat that comes through glass in these cases becomes the dominant design issue then. It should be recognized that heat travels through glass both from the sun’s direct radiation and from the transfer of heat from the ambient exterior environment. Therefore, selecting glass that provides solar control to address both the sunlight and ambient heat reflectance will maximize performance.

Glass can provide direct solar control by one of two fundamental choices. First, it can absorb a portion of the solar energy striking it through the use of absorptive colored tints or absorbing coatings added to the glass. This significantly reduces solar heat and UV light transmittance as compared to clear glass products. Tints add color to the look of the building and reduce the visible light transmittance (VLT) through the glass, all of which are variable based on the degree of tinting and color selected. The key to selecting tinted glass is finding the balance to achieve solar control, help control glare and contribute to the aesthetics of the building. Tinted glass is readily available in a variety of thicknesses (generally between 1/8 inch and 1/2 inch) and can be processed and fabricated similarly to normal float glass making it a convenient way to reduce solar gain. Tinted glass features a full range of color choices such as green, blue, blue-green, bronze, and grey colors. They commonly provide low external and internal reflectance meaning that they are not very mirror-like. They can be laminated, strengthened, and even bent using standard techniques. Further, they can be used singly or in combination with other glazing in insulating glass units. All of these traits have made tinted glass a common solar control choice in low, mid, and high rise office buildings, medical / hospital buildings, educational / school buildings and retail locations.

Image courtesy of Pilkington North America

The chart depicts the percentage transmittance of typical glass types and colors. It demonstrates how tinted glass lowers SHGC through a reduction in transmittance in the Solar Infrared region, while maintaining high light transmittance in the Visible Light region.

Instead of absorbing energy, the other choice of achieving solar control with glass is to reflect it back varying degrees of solar light or heat energy (or both) by applying various coatings during manufacturing. The types and effectiveness of the coating can vary notably between glass products and between manufacturers so it is important to review the technical data to be sure that a coating is selected appropriate to the building, its location, and solar orientation. For example, a coating that produces a low SHGC value will result in very little solar heat passing through the glass while a low-e coating reduces the emissivity of glass and lowers the U-factor. Some manufacturers have coatings that will achieve both solar control and low emissivity and those should be looked at for suitability. Coated glass is available in some fairly clear versions or in a full range of colors including green, blue, blue-green, bronze, gold, and grey. The coatings also commonly reduce UV light transmittance which means fading is reduced in fabrics, artwork, etc. Coatings have been recognized as an ideal means to achieve a rather precise level of solar control for new commercial construction or renovation projects. Specifically by using different coatings on different layers of a dual pane insulated glass unit, the options and possibilities increase for balancing heat gain against light transmittance and U-factors. Hence, coated glass has been commonly used in commercial buildings requiring solar and thermal control such as low, mid and hi-rise buildings, medical/ hospital buildings, educational/ school facilities, office buildings, retail establishments, and residential structures of all types.

Controlling Heat Loss

Turning to colder climates, the approach to thermal energy performance with glass is different. In these locations, the energy required for heating is greater than for cooling over the course of the year. Hence, there is usually a desire to allow sunlight to freely penetrate into the building during the heating season to take advantage of passive solar gains. This means selecting glass with a higher SHGC may be desirable, particularly on sun facing facades. At the same time, low emissivity is desired to redirect energy (i.e. interior room heat) back into a building (rather than out of it), to achieve much lower heat loss than ordinary float glass. For such buildings, this coating is often selected to allow for enhanced clarity and light transmittance which will tend to favor a pyrolytic surface coating over a sputter coating. Once again, the use of different coatings on different layers of insulated glass units allows for some fine tuning of the glazing to suit particular circumstances of different buildings, different solar orientations and different performance needs. The surfaces of insulated glass units are identified by number such that in a typical double pane unit, surface #1 faces the building exterior, #2 is the inner face of the outer pane (in the space between the glass layers), #3 is the exterior face of the inner pane (also in the space between glass layers), and #4 faces the building interior. Usually the coatings are placed on surfaces #2 and #3 so they are not exposed.

Image courtesy of Pilkington North America

Use of a low-e coating on surface #4 in combination with a low-e coating on surface #2 provides a significant reduction in U-factor of approximately 20 percent.

Low-e 4th surface technology

In order to improve the energy efficiency of insulated glass units without increasing the thickness or weight of the window, at least one manufacturer has developed a coating for the 4th surface of the double glazed unit. This 4th surface coating works in combination with a low-e coating on surface #2 to create a significant reduction in U-factor of approximately 20 percent. Pyrolytic Low-E coatings are well suited for this purpose as they provide the advantage of being very durable and difficult to damage, with a track record of use in these types of application for well over 10 years.

Daylighting and Views

In some cases, the visual performance of the glass may be the overriding design issue. This can be true in buildings where daylighting is being used to turn off electric lights and save energy or in cases where the ability to view through the glass with clarity and good color rendition is important. Note that all of the glass discussed for thermal energy performance provides some degree of visual performance and the glass described in this section provides some degree of thermal performance. The distinction is the degree to which the two are balanced or weighted to favor one over the other due to its specific location in a specific building.

Among the things to take into account in selecting glass for daylighting is the quality of the light that will end up in the interior space. The color of the glass or the coating can affect the color of the transmitted light while clear glass will allow for more accurate color renditions. However, clear glass can be a source of glare. If the glass is not shaded, does not face away from the sun, or is not treated to reduce glare, then the shear light intensity or the high contrast between it and the other interior spaces can create disturbing and unwanted bright light. In that case people will often respond by closing blinds or otherwise block the daylight undoing the intended benefit of the design. Selecting a tinted or coated glass therefore that appropriately addresses glare while still keeping the color clear may be an optimal solution in some cases.


Photo courtesy of Pilkington North America

The quality and the quantity of light are important factors for spaces that are naturally daylight using glass.

In addition to letting daylight into buildings, allowing people to view out without undue color or view quality issues is also a common design requirement. Clear glass is available that offers excellent optical properties, transmitting up to 90 percent of the sun’s visible spectrum thus maintaining high clarity and low distortion with brilliant flat surfaces. It is available in a wide range of sizes and thicknesses for optimum utilization and is applicable in commercial, residential, and institutional buildings of all types.

Safety Glass

There are many interior and exterior applications where codes and general practice require the use of safety glass that reduces the possibility of injury if broken. Tempered glass is commonly used, although the tempering process introduces distortion in the glass which can give the unwanted characteristic of visual waviness. Furthermore there is a small risk of spontaneous breakage when using tempered glass, which restricts its use in certain applications. Heat strengthened and laminated glasses are options to mitigate these issues. One thing to be aware of however, is that heat treating float glass to produce either heat strengthened or tempered glass requires a focused cooling process called quenching. The quenching air jets used in a tempering furnace cannot cool the glass with complete uniformity though. As a result some areas are cooled faster than others, resulting in differential shrinkage which creates areas of different compressive stress. This differentiation can create “quench marks” due to very slight changes in the glass density which affects the light passing through the glass. Quench marks should not be considered a defect; they are an indication that the glass has been heat treated. Appearance of quench marks is dependent on lighting conditions and they can be visible in transmission and reflection, and particularly when viewing the glass at an angle other than directly facing the glass. They are more visible in thicker, clear, heat treated, glass; when a lightly reflective coating is used; or when both lights of glass in an insulating glass (IG) unit are heat treated. They become particularly visible in any glass when polarizing sunglasses are worn. Therefore, if viewing clarity is the priority, designs which do not require heat strengthened or tempered glass can be preferable to those that do. It is always important to construct a mock-up of the intended glazing design to gain an understanding of any potential issues related to distortion or quench marks.

Visual Clarity

There are many applications where glass is used and great visual clarity is the major design criteria. This might include retail displays, showrooms, museums, sports stadiums, zoo enclosures and exhibits. In these cases glass is commonly used to create a physical barrier but clear visual characteristics are needed without distortion. Since visual clarity is affected by the amount of visual reflections that appear on the surface of the glass, anti-reflective glass is available to overcome this issue. It is formed by using two pyrolytic coated surfaces in a single laminated glass product to minimize visible light reflectance to less than 2 percent compared to normal clear glass which is 8 percent. This allows more than 90 percent of visible light to transmit through the anti-reflective laminated glass with very low masking reflections. In addition, anti-reflective glass can block more than 99 percent of transmitted UV thus reducing the fading of interior fabric and furnishings. As a laminated glass product, it also offers the traditional benefits of enhanced security, improved safety, and damage protection. It is possible to get anti-reflective glass tempered if increased strength is required. One manufacturer produces an anti-reflective glass that offers a lower emissivity than normal glass; giving improved thermal insulation in addition to a reflection reduction.


Photo courtesy of Pilkington North America

Ordinary glass on the left can produce veiling reflections that obscure the view through to the other side. Anti-reflective glass on the right dramatically improves the clarity of objects beyond the glass.

For situations where very pure color clarity and high VLT are desired, low iron glass may be worth considering. Normally, all glass has traces of iron content which is responsible for the edges of a piece of clear glass appearing green. When glass is manufactured by deliberately reducing the amount of iron present, the green edge color is reduced in intensity and the view looking through the glass is very clear. It is therefore ideal for use where glass edges are visible or where a neutral color is desired. As its light transmission is 1 percent and 8 percent higher than clear float glass in 3 mm to 19 mm thickness respectively, it is perfect for applications where transparency and purity of color are desired. It can be used in anti-reflective glass, in insulated glass units, and for maximizing solar heat gain in colder climates. Low-iron glass can also be heat treated for safety and laminated for security. All of these traits make it a high clarity choice for storefronts and displays, furniture, solar collectors, photovoltaic panels, and special applications requiring thick glass such as bullet resistant glass, aquariums etc.


Photo courtesy of Pilkington North America

Low-iron glass shown on the left is more optically clear without the common green tint found in most conventional glass products as seen on the right, particularly along the glass edges.

Special Building Design Applications

There are a number of building design situations where some very specific needs arise for glass. Manufacturers have responded by developing and testing glass products to meet those special applications.

Fire Resistance with Glass

For building areas that require viewing through glass but also high levels of fire protection, then fire-resistant glass should be considered. It is specifically designed to limit conductive and radiative heat transfer with product performances ranging from 20 to 120 minutes. These glass products must always be used as part of an approved fire resistance or fire protected framing assembly. Fire-resistant glass consists of multiple laminates of float glass and a special transparent intumescent interlayer, which is totally compatible and optically homogeneous with the glass. When exposed to fire, the pane facing the flames fractures but remains in place. As the heat penetrates the glass, the interlayers react by foaming to form a thick, opaque, resilient and tough insulating shield that blocks the conductive and radiant heat of the blaze. As a design tool, it allows natural light and unobstructed views in fire rated walls, openings and doors while restricting the spread of heat, smoke, flames and hot gases. It can be combined with a full range of other glass products to address security, bullet and hurricane resistance or visual clarity requirements. These products are typically tested and classified independently by organizations such as Underwriters Laboratories (UL). Ultimately, it addresses health safety and welfare by reducing fire damage to people, property and valuables.


Photo courtesy of Pilkington North America

Fire-resistant glass can be used to spread daylight and create open visual contact in areas that require fire resistance ratings in buildings.

Acoustic Control

Some buildings are subject to higher levels of noise than others while some building uses are simply more sensitive to noise affecting the occupants / users of that building. Either way, unwanted noise coming from things like roadway traffic, railways, aircraft, factory operations, music, or other activities needs to be limited and controlled. Methods of creating sound insulating walls are common and fairly well known, but if those walls have windows, the glass needs to provide acoustic control as well. Noise control glass is the ideal choice in situations like this. By using a polyvinyl butyral (PVB) interlayer laminated between two layers of selected float glass, manufacturers offer a high quality product that produces excellent noise reduction without compromising on light transmittance or impact resistance. The acoustic performance can be varied by combining different thicknesses of glass with the PVB interlayer to achieve a specified rating. In this way noise control glass offers the opportunity to achieve project-specific noise reduction requirements. It is generally available in a variety of sizes and can be fabricated to meet any needed safety ratings. It can be used singly or in double or triple pane Insulating Glass Units (IGUs). Depending on the configuration and thickness of the glass, test results have shown that noise control glass can achieve STC ratings between 31 and 39. One manufacturer offers a laminate with a special PVB that specifically reduces mid-range frequencies and tests with an STC in the low 40s. Attenuation of mid-range frequencies is important as this includes sounds such as urban road traffic, railway traffic, music and factory noise.

Self-cleaning Exterior Glass

Buildings of many types that contain glazing that is difficult to reach for cleaning or simply require cleaning because of the surrounding environment can create ongoing high maintenance expenses. In response, a rather innovative glass product has been developed that uses the power of the sun to clean itself. This self-cleaning glass can dramatically reduce or eliminate window cleaning, while still offering good visual clarity and an unspoiled exterior aesthetic. This glass uses UV energy from the sun, which is abundant even on cloudy, overcast days, to keep windows clean naturally in several steps. First, a photocatalytic process generated by additives in the glass loosens dirt and gradually breaks down organic residue so it doesn’t adhere to the glass. Next a hydrophilic action on the glass surface causes rain to sheet on the glass, carrying dirt away with minimal spotting or streaking. Under most conditions, natural rain is sufficient to keep the window clean, and a quick spray with a hose will achieve the same result even in prolonged dry weather. Since the coatings used in this self-cleaning glass are pyrolytic and an integral part of the glass surface, they aren’t susceptible to peeling, separation or disintegration over time. In addition, they are not damaged by liquid glass cleaners so there is no need to be concerned about re-coating or retreating the glass. Combined in an insulating unit with an inboard lite of either low-e or solar control glass, all aspects of glazing performance in a building can be addressed and maintained. Self-cleaning glass is commonly available in clear or blue colors and a range of thickness from 1/8 inch up to ¼ inch.

Emerging Technologies

While all of the glass types and products discussed so far represent a fair amount of innovation and technological advances, manufacturers are continuing to pursue even more ways to address building design issues through advanced products. Some of these include the following cutting edge glazing innovations.

Vacuum Insulated Glazing

A vacuum, is very effective at minimizing conduction and convection heat losses. While a perfect vacuum with zero heat transfer is not easily achievable, it is possible to produce a partial vacuum with notably reduced heat transfer. These insulating principles of vacuums are being applied by some manufacturers to create a high performance glass with a thinner profile. They are offering vacuum insulated glazing that is different than conventional double glazing in that the air between the two panes of glass is extracted, to create the needed vacuum. In order to keep the panes from collapsing in on each other, micro-sized spacers are used to keep the panes apart. Nonetheless, the gap between the two panes can be reduced to just 0.2 mm, giving the glass an overall thickness of just over 6 mm (1/4 inch). Heat flow through radiation can be reduced by covering one of the glass panes with a low-emissivity coating, similar to that used in conventional double glazing. Therefore, despite its thin profile, vacuum insulated glazing can achieve U-factors as low as 0.18 Btu/hr.sqft°F in a ¼ inch profile. That means the same or better thermal performance is achieved as conventional double glazing but in one quarter of the thickness and two thirds the weight. That makes it ideal for retrofit or historic preservation projects where an existing window sash or frame needs to be preserved and conventional insulated glazing units won’t fit. Thus it balances historical preservation with modern comfort and environmental requirements while allowing windows that are more in keeping with the original design.

There are of course some variations available for vacuum insulated glazing. For locations that require solar control, the coated surface can be designed to achieve the needed SHGC. For situations that can accommodate the width of IGUs, it is possible to use a triple glazed, coated vacuum insulating glass unit that gives U-factors as low as 0.12 Btu/hr.sqft°F. This combination uses a vacuum insulated glass unit with a conventional spacer, gas fill and a coated outer pane to create a hybrid unit with superior thermal performance. Both designs allow for minimum disruption in existing buildings making it a cost effective method of improving the energy efficiency. The vacuum also allows for improved acoustic performance over single glazing, enhancing the living and working environment. While this is regarded as an emerging technology in the US, it should be noted that it has been successfully used in Japan for over fifteen years and is really a proven solution.


Photo courtesy of Pilkington North America

Vacuum insulated glazing uses clear micro spacers to keep the panes separated but still allows for good visual clarity in the size and weight of glass suitable for historic renovations.

Specialty Glazing

Manufacturers continue to expand and develop the range of coatings that can be used on glass to meet very specific and special needs. As a result, specialty glass has become available that can be used to meet those needs. For example, controlling condensation on glass doors of built in refrigerators / freezers in supermarkets or other retail settings can be an ongoing problem both for maintenance and for visibility of merchandise. As a result, electrically conductive glass has been developed that allows the glass to be electrically heated and overcome this problem. It is color neutral, minimizing reflected color and will not change over time. It easily fabricated with a durable pyrolytic coating that can be handled, cut, insulated, laminated, heat-strengthened and tempered and is even bendable. The heated glass is scratch and abrasion resistant and is available in a variety of glass thicknesses and sheet resistances ranging from 5 ohms/square up to several thousand ohms/square. As a result, heated glass combines thermal control with superior electro-optical properties to keep merchandise clearly visible. Heated glazing has also been used in a variety of architectural applications, such as in restaurants where thermal comfort of the diners is important. Here the heated glazing provides heat to the building occupants.

Other specialty glazing has been developed for electro-optical applications such as computer screens or touch screens in buildings or glazing that will control static when touched. For buildings that want to use photovoltaic (solar-electric) energy, specialty glass and glazing has been developed for both rigid panels and thin film applications. The rise in the use of building integrated photovoltaic cells (BIPV) is made possible because of the effective development and proper use of this type of specialty glazing that maximizes the energy generating potential of these systems.

Electrically conductive specialty glass can be used to keep glass panels clear in retail settings where commercial refrigeration is used.
Photo courtesy of Pilkington North America

Electrically conductive specialty glass can be used to keep glass panels clear in retail settings where commercial refrigeration is used.

Switchable Electrochromic Glazing

When glass is tinted or coated it achieves the resultant performance properties permanently. This means that the glass performs the same way all the time regardless of any changing light conditions outside. An innovative alternative is to use glass that can literally be switched from clear, to lightly tinted to dark tinted and levels in between. This is being achieved by using electrochromic coatings which are applied to panes of conventional float glass or float glass coated with transparent conductive coatings. Electrochromic coatings are typically metal oxides and are thin films like other glass coatings. When a very small electric voltage is applied across the coatings, ions travel between layers, where a reversible solid state change takes place, causing the coating to tint and absorb light. Reversing the polarity of the applied voltage causes the ions to migrate back to their original layer, and the glass returns to its clear state. This ability to switch glass back and forth at will is particularly useful and desirable in large daylit spaces where different uses and lighting conditions dictate different needs for the glass. Typically electrochromic glazing should be integrated into the building control system to maximize efficiency. Other types of switchable glazing are available, including LCD based privacy glass and thermochromic and photochromic based materials.

Green Building Contributions Of Glass

The US Green Building Council (USGBC) has developed the LEED® rating system for green buildings which has been recognized as the leading green building standard in this country. The LEED 2009 system is in place until the year 2015 which overlaps with LEED version 4 introduced late in 2013. Since buildings are currently being designed under both systems, credits available for both are summarized below which properly selected glass products can contribute to.

Optimize Energy Performance

Both LEED 2009 and LEED v. 4 place a strong emphasis on reducing the use of fossil fuels and increasing the use of non-polluting renewable energy. As we have seen, the range of glass products available allow architects and other design professionals to truly optimize performance by selecting glass that is coated, tinted, or otherwise fabricated to best suit a particular building and its location, and even vary the selections to suit individual building facades and installations. If on-site renewable energy is pursued, it is likely that photovoltaic solar cells will be considered which the properly selected glass will support and make possible. In order to receive points in this credit category the building must demonstrate a percentage increase in energy savings in accordance with ASHRAE standards. The number of points earned depends on the degree of energy savings and/or the amount of energy generated on site.


Photo courtesy of Pilkington North America

Solar photovoltaic systems rely on appropriate solar glass to allow the optimization of energy being produced without relying on any fossil fuels.

Materials and Resources

This area has changed dramatically between the different versions of the LEED® rating system. LEED 2009 includes four areas where metal wall panels can contribute to an overall green building:

 

MR Credit 4: Recycled Content: 10 percent and 20 percent (1 – 2 points) Post-consumer glass is a highly recyclable material that can be re-used or repurposed into a variety of products such as glass containers, counter tops and landscaping material. However, it cannot be utilized in the float glass manufacturing process since even the smallest impurity can compromise the product quality and manufacturing process. Therefore, float glass manufacturing cannot utilize recycled glass as defined by the LEED rating system.

 

Credit 5: Regional Materials (1 – 2 points). Many glass manufacturing plants are located throughout the USA meaning a regional material contribution is possible depending on proximity to the building.

The Materials and Resources category under LEED v. 4 takes a rather different approach to defining the green nature of building products. The new approach focuses on the full life cycle of those products. The key documentation needed to demonstrate performance under this approach is referred to as an Environmental Product Declaration (EPD). Individual manufacturers or a trade association can prepare specific or generic EPDs for products. In the case of glass products, check with the manufacturer to see what is available for documentation to earn the appropriate points for this updated category.

Indoor Environmental Quality

Under IEQ Credit 8.1 Daylight & 8.2 Views, glass plays a very significant role as has been discussed. The beauty of the range of glazing choices is that daylight can be brought into spaces while still addressing the thermal needs of the building and without blocking the view. Glass products have daylight transmissions ranging from 92 percent down to 8 percent, when single glazed. As outdoor daylight (no direct sun) is in the 1,000 to 2,500 foot candle range, even the lowest transmission (darkest) glass in large sizes, can meet the minimum credit requirement with only 8 percent transmittance of 1000 foot candles (i.e. 80 fc luminance).

Innovation in Design

Under both LEED 2009 and LEED v. 4, credit is given for recognized innovations that exceed minimum performance levels in green building components or systems. Hence, it is entirely possible to achieve some additional credit by using some of the innovative or emerging technologies related to glass that improve on LEED minimum performance levels. More significantly, it is possible to show innovation by using these systems to improve the building overall by finding appropriate ways to address differing needs and strike the right balance between them under different operating conditions.

Case Study

Michigan State University Federal Credit Union Headquarters Building

 

Location: East Lansing, Michigan

 

Architect: Daniels and Zermack Associates, Inc.

Gregory A. McKenzie, AIA, Principal-in-Charge, Ann Arbor, MI

Glazing Contractor: Calvin and Company of Flint, MI

Glass Fabricator: PDC Michigan of Plymouth, MI

Glass used: Solar Control Low-e coated

Celebrating its grand opening of a new headquarters building in East Lansing, MI, the Michigan State University Federal Credit Union (MSUFCU) is setting the standard for green construction and sustainable design. The new Gold LEED® Certified, 145,000-square-foot building, along US-127, is the permanent location for the company headquarters. Operating for over 73 years, MSUFCU is the largest university-based credit union in the world. With its primary focus being its members and community, the construction of the new headquarters building proves to be a valuable contribution. MSUFCU in collaboration with Architects, Daniels and Zermack Associates, Inc. in Ann Arbor, MI, have integrated green design and construction materials for an energy efficient, sustainable project.

Daniels and Zermack have been providing innovative building design to financial institutions for over 60 years. The full service firm specializes in new construction, additions, planning, and renovations. Greg McKenzie, AIA, Principal-in-Charge of the project, took the efficiency of the building into great consideration during design. McKenzie worked closely with Glazing Contractor, Calvin and Company of Flint, MI and Glass Fabricator, PDC Michigan of Plymouth, MI to select the best possible glass choices to achieve the desired outcomes. The four story headquarters building showcases 44,000 square-feet of solar control, low-e glazing selected for this project because it provides a perfect blend of visible daylight along with low solar heat gain. The low-emissivity properties combined with solar control result in energy cost reductions compared to ordinary glass.

Overall, nearly 80 percent of the building takes advantage of natural day lighting to reduce the need for artificial lighting,” according to McKenzie. However, MSUFCU wanted a building that did not require the use of blinds since they were viewed as an added cost that compromises the appearance of the building from the exterior. The selected glazing provides glare control which allows for this design option. The contemporary building design blends the aesthetics of all the branch locations, which showcase brick and green glass facades. McKenzie said, “The glass is a great color match and we are very pleased with the result.” The building’s attractive low-e glass facade allows natural light in, absorbs and blocks solar energy, reducing the amount of heat that can enter the building. It combines great aesthetics, solar and thermal performance, subtle reflectivity and glare control all in the final design.

Conclusion

Architects design buildings to meet a variety of criteria and in so doing combine professional skill with appropriate material and product selection. Float glass has been shown to be a vital and integral building material that is manufactured in a full range of products to address many general and very specific design issues. As such, architects are now able to select specific glass products for different projects and façades from a vast range of combinations of tempered, laminated, tinted and coated glass. By understanding the differences and benefits between the different manufactured choices the performance, aesthetics, and functionality come together to create building designs that can meet or exceed expectations.

Peter J. Arsenault, FAIA, NCARB, LEED AP, practices architecture, consults on green and sustainable design, writes on technical topics, and presents nationwide on all of the above. www.linkedin.com/in/pjaarch


As a leading global glass manufacturer, the NSG Group provides one of the broadest ranges of glass products available in the world today. Pilkington products help control energy usage, protect against fire, insulate against noise, provide safety and security, afford decoration and privacy, incorporate self cleaning properties and are used in all-glass facades. www.pilkington.com/na

Source  : NSG Group

(0)

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Nam augue lectus, interdum ut lorem eu, interdum mattis massa. Donec consectetur tempor imperdiet. Donec turpis augue, consectetur ut pellentesque ac, rhoncus quis dui. Morbi sagittis quam nec dui dignissim, ac rhoncus augue varius. Vestibulum sed nunc laoreet, ullamcorper mauris id, commodo nisi. Ut semper est diam, et imperdiet urna aliquet at. Duis et orci ac turpis convallis interdum ac in sem. Morbi laoreet pellentesque tempor.

Continue Reading…

(0)

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Nam augue lectus, interdum ut lorem eu, interdum mattis massa. Donec consectetur tempor imperdiet. Donec turpis augue, consectetur ut pellentesque ac, rhoncus quis dui. Morbi sagittis quam nec dui dignissim, ac rhoncus augue varius. Vestibulum sed nunc laoreet, ullamcorper mauris id, commodo nisi. Ut semper est diam, et imperdiet urna aliquet at. Duis et orci ac turpis convallis interdum ac in sem. Morbi laoreet pellentesque tempor.

Continue Reading…

(0)

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Nam augue lectus, interdum ut lorem eu, interdum mattis massa. Donec consectetur tempor imperdiet. Donec turpis augue, consectetur ut pellentesque ac, rhoncus quis dui. Morbi sagittis quam nec dui dignissim, ac rhoncus augue varius. Vestibulum sed nunc laoreet, ullamcorper mauris id, commodo nisi. Ut semper est diam, et imperdiet urna aliquet at. Duis et orci ac turpis convallis interdum ac in sem. Morbi laoreet pellentesque tempor.

Continue Reading…

(0)

[ig_row][ig_column span=”span12″ css_suffix=”col-sm-12″[ig_row width=”boxed” r_class=”none” t_class=”none” background=”none” relative=”no” video_b=”no” border_width_value_=”0″ border_style=”solid” border_color=”#000″ div_padding_top=”30″ div_padding_right=”30″ div_padding_bottom=”30″ div_padding_left=”30″ css_suffix=”special” ][/ig_row]][ig_text]Lorem ipsum dolor sit amet, consectetur adipiscing elit. Nam augue lectus, interdum ut lorem eu, interdum mattis massa. Donec consectetur tempor imperdiet. Donec turpis augue, consectetur ut pellentesque ac, rhoncus quis dui. Morbi sagittis quam nec dui dignissim, ac rhoncus augue varius. Vestibulum sed nunc laoreet, ullamcorper mauris id, commodo nisi. Ut semper est diam, et imperdiet urna aliquet at. Duis et orci ac turpis convallis interdum ac in sem. Morbi laoreet pellentesque tempor. Continue Reading…

(0)

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Nam augue lectus, interdum ut lorem eu, interdum mattis massa. Donec consectetur tempor imperdiet. Donec turpis augue, consectetur ut pellentesque ac, rhoncus quis dui. Morbi sagittis quam nec dui dignissim, ac rhoncus augue varius. Vestibulum sed nunc laoreet, ullamcorper mauris id, commodo nisi. Ut semper est diam, et imperdiet urna aliquet at. Duis et orci ac turpis convallis interdum ac in sem. Morbi laoreet pellentesque tempor.

Continue Reading…

(0)